Skip to content

Prevention

Water Heater Maintenance

What flushing a tank actually removes, how the anode rod protects the steel, why hard water makes both jobs more urgent, and when maintenance is too late to help.

Two jobs, done on a schedule, extend a tank's life: draining the sediment out of it, and replacing the sacrificial rod before it is used up. Everything else in maintenance is a look at things that might fail.

What flushing removes

Water carries dissolved calcium and magnesium, and heating precipitates them. The minerals settle on the tank floor and on the heating surface. The layer insulates, so the burner or element works longer and hotter for the same hot water, and the popping or rumbling sound homeowners describe is steam forming under it.

Flushing drains the tank and refills it, carrying the loose sediment out through the drain valve. It does not dissolve the scale bonded to the heating surface, and it does nothing at all for a tank that has already corroded through.

Why the anode rod matters more

Inside every steel tank is a rod of a more reactive metal, magnesium or aluminium, sometimes powered. It corrodes instead of the tank, which is why it is called sacrificial. When it is consumed, the tank shell starts to go, and that is the failure nobody can repair.

Checking it means removing it, which on many units is a job in itself: clearance above the unit, a socket, and sometimes a rod that will not budge. Replacing a spent rod is one of the few maintenance actions that measurably delays a replacement.

Signs to act on

  • Popping or rumbling when the burner fires or the element heats.
  • Hot water that runs out faster than it used to.
  • The temperature set higher than it once was to get the same result.
  • A relief valve that weeps.
  • Water that looks rusty at the hot tap.

The first four point at sediment and scale. Rusty hot water can also mean a failing anode or a corroded dip tube, both worth finding out about before the tank fails.

What hard water means here

San Gabriel Valley Water Company's 2025 consumer confidence report lists hardness averaging 234 ppm over the 2022–2025 sampling, within a 189–280 ppm range. On the USGS scale that is very hard water, and it is why maintenance matters more here than in a soft-water region: the same tank, flushed and re-roded, behaves very differently from one that is not.

Which utility serves a particular address varies by city, so the figure is regional context rather than a measurement of your tap.

When maintenance is too late

A tank with water at its base, rust streaks on the shell or a bulge is beyond maintenance. A tank that has gone a decade without attention may also be past the point where a first flush helps: disturbing a heavy sediment layer on a corroded floor can start a leak that ends the unit.

That risk is worth saying out loud rather than discovering, and it is the reason an older tank's first flush should be judged on the unit's age and condition, not scheduled automatically.

Tankless maintenance

A tankless unit does not accumulate sediment in a tank, it coats its heat exchanger. Descaling, which means circulating a mild acid through the unit, is the equivalent job, and on very hard water it belongs on a schedule. Inlet filters also need cleaning, more often than the default in the manual suggests.

Water Heater Maintenance service areas

How coverage is decided

Get in touch

Tank making noise or running out faster?

Both usually mean sediment. A flush is cheap next to a replacement, and the call is where it gets judged against the tank's age.

Questions about this service

How often should a tank be flushed?

Frequency follows water hardness and use, so there is no single interval that fits every house. On very hard water a yearly flush is the common starting point, and a household that has never flushed an older tank should expect the first one to be a judgement call rather than a routine job.

Do I need to turn off the power or gas to flush a tank?

Yes. An electric unit is shut off at the breaker and a gas unit at its control before any water is drained, because a heating element or burner firing with the tank partly empty can be damaged or become dangerous.

Call+1 989 601 2666